Suction line drier

The ASD is a premium suction line filter drier for use with CFC, HCFC and HFC refrigerants. The ASD is optimized for high moisture, aci and solid contaminant removal. The Catch-All has been designed to do the job with maximum efficiency. Suction Line Filter-Driers.

Brand: Emerson Flow Controls.

The features of the steel liquidline filter- drier when combined with the steel suction - line drier make the pair an excellent solution for system cleanup. The two driers will quickly and effectively remove the water, sludge, acids, and solid contaminants generated when a system fails. Alternatively, 96-TS filter driers can be installed as a suction line filter drier in remote systems with long refrigerant lines. Make sure the suction line adjacent to the compressor is clean.

Install an Emerson suction line filter-drier. Pressure and leak-test the system according to the unit manufacturer’s recommendations. Triple evacuate to at least 5microns.

Break the vacuum with clean, dry nitrogen at psig. If a suction vibration eliminator is use the drier or filter should be installed upstream of it. Liquid… what is the difference between.

Stock up on suction line driers in the parts and supplies department of LennoxPros. The obvious benefit of a suction line filter drier is the added protection given the system if a burnout should occur. The filter will effectively prevent contamination resulting from the failure from traveling back through the suction line into the other parts of the system.

The PARKER steel shell suction line filter dryer is designed for system cleanup. Compact design incorporates large outside diameter shell for shorter lay-in length, and a larger core for a greater filtration area for maximum operating efficiency. Here, courtesy of Emerson, is a look at the safety and installation tips related to suction line filter-driers. Read the instructions thoroughly. Failure to follow instructions may result in filter- drier failure, system damage, or personal injury.

The system must be pumped down and line depressurized before attempting to install. A suction line accumulator prevents compressor damage from a sudden surge of liquid refrigerant and oil that could enter the compressor from the suction line. The suction line accumulator is a temporary reservoir for this mixture, designed to meter both the liquid refrigerant and oil back to the compressor at an acceptable rate.

A liquid line drier goe in the liquid line NOT in the discharge line.

The discharge line is between the compressor and the condenser. The liquid line is between the condenser and the metering. This one looks at the parts of the drier. Welcome to Hvacproforums, an interactive community exclusively for HVAC professionals. The collective years of HVAC experience and the knowledge our forum members share make this an invaluable resource for those in the HVAC industry.

Where must the suction line drier be placed after a motor burnout? Drier removes much more acid (on an equal weight basis). If you do choose to LEAVE a suction drier in a system there are a few things to consider. The SFD is a standard suction line filter- drier for use after a burnout or when major work has been performed.

It is good practice to install the suction drier in the true suction line on heat pumps , you definately dont want it in the discharge line. A manufactured device used in the suction line of a refrigeration system, whose element is partly or wholly composed of a desiccant. Emerson EK-1liquid line filter driers being installed on site.

This device is used to protect the compressor especially after any failure that contaminates the system. Refrigerant Filters-Dryers Products from parker include. Replaceable Core Filter- Drier - Parts. The Parker Type SLD series suction line filter driers contain a. A suction line filter dryer protects the compressor from debris such as copper pipe filings, braze and solder. Dual access valves on both the inlet and outlet sides for easy pressure readings.

Cause Roy said so and cross your fingers. Must of been a tough system though. Change out the liquid line drier also. But there are basics to physics. Some manufacturers say that a suction line filter drier does a better job of removing moisture from the system.

That is because the moisture tends to condense in the cold suction line and is easily trapped by the suction line filter drier. However, a suction line drier is only used for clean up purposes, say after a burnout. The following is a selection of Sporlan references available for download. All information is in portable document format (.pdf).

Another type of liquid line drier has been especially developed for use on heat pump. The filter drier will collect and hold any dirt that is in the evaporator or suction line at start up. The desiccant block core effectively removes and holds a maximum amount of contaminants with minimum pressure drop.

The blend of desiccants used in the Catch-All Filter- Drier are specially formulated for exceptional water removal. How to prepare for the installation of a Filter Drier David Jones. GOT2LEARN - Duration: 10:07.